Medical-Grade Red Light Therapy Mask
- LED Configuration: 93 premium LEDs (279 chips)
- Wavelengths: 415nm (Blue), 633nm (Red), 850nm & 1072nm (Near-Infrared) – for acne care, collagen regeneration, skin repair, and anti-aging.
- Irradiance: 35–40mW/cm² for effective light penetration.
- Treatment Modes: 2 therapy programs | 3 brightness levels | 10Hz pulse function.
- Certifications: FDA 510(K), CE, FCC, RoHS, Australia SAA, TGA, MDL, ISO13485, IEC60601.
- 60-Day Money-Back Guarantee
Step 1: Charge before first use
Charge the mask fully via the included USB cable before your first session. The built-in 4000mAh battery provides multiple sessions per charge. Use the mask only when fully charged for your first use to confirm everything is working correctly.
Step 2: Cleanse your skin
Wash your face and pat dry. Remove all makeup, SPF, and skincare products before putting the mask on. Clean, bare skin allows the light to penetrate without any barrier. Do not apply serums or oils before the session — apply them after.
Step 3: Put on the mask and adjust fit
Place the mask over your face with the LEDs facing the skin. Use the adjustable straps to secure it comfortably. The soft liquid silicone should sit flush against your face without pressing too hard. Lie back or relax in a chair — no need to hold the mask in place.
Step 4: Select your mode using the remote control
Use the included remote to choose your treatment mode:
Anti-Aging Mode (630nm + 850nm + 1072nm):
Best for fine lines, collagen support, skin firmness, and overall rejuvenation. Use this for your regular maintenance sessions.
Anti-Acne Mode (415nm + 850nm + 1072nm):
Best for active breakouts, oily or congested skin, and reducing surface inflammation. The blue light targets acne-causing bacteria while the 850nm and 1072nm support healing.
Step 5: Set brightness level
Use the remote to cycle through 3 brightness levels (50% / 75% / 100%). If you're new to light therapy, start at 50% for your first few sessions and work up to higher intensities as your skin adjusts. You can also activate Pulse Mode (10Hz) for a rhythmic light cycle.
Step 6: Relax for 10 minutes
The mask runs on a pre-set 10-minute session. The device will shut off automatically. Do not look directly at the LEDs during use. Close your eyes, relax, or use the time to meditate or listen to music.
Step 7: Apply your skincare immediately after
Remove the mask and apply your serum, moisturiser, or eye cream right away. Light therapy temporarily increases skin permeability — your products absorb more effectively in the 20–30 minutes immediately following a session. Avoid retinol or exfoliating acids directly before or after sessions.
Recommended frequency: Daily or 3–5 times per week for best results. Consistency over weeks is what drives visible change.
Important: Avoid direct eye exposure to the LEDs. Contact lens wearers should remove lenses before use. Do not use on open wounds, active skin infections, or within 2 weeks of facial surgery or laser procedures.
1 × Face Mask
1 × Remote Control
1 × USB Charging Cable
1 × Travel Storage Bag
1 × User Manual
Do not use this Mask if you:
- Are pregnant, planning to become pregnant, or breastfeeding
- Have known photosensitivity or take medications that increase sensitivity to light
- Have a history of light-triggered seizures or epilepsy
- Have been diagnosed with skin cancer or active cancer in the treatment area
Avoid direct exposure to the eyes. This device is intended for external use only. Discontinue use if redness, irritation, or discomfort occurs.
One mask. The right wavelengths. Nothing else comes close.
Clinical results at a fraction of the price.
- FDA 510(k) cleared — not just "compliant"
- Four wavelengths, including 1072nm
- Pays for itself in two clinic facials
- Wireless — use it anywhere
Smart & Simple Controls
- Treatment Time: Default 10-minute session (optimized and pre-set)
- Brightness Levels: 100%, 75%, and 50% dimming options
- Pulse Function: 10Hz pulsed LED light for enhanced comfort and effectiveness
- No complicated settings—simply press and relax
1072nm Infrared Skin Therapy
Deep-penetrating infrared wavelength designed to reach subdermal layers, supporting collagen renewal and improving visible signs of aging from within.
Focuses on:
- Deep wrinkle areas
- Skin firmness loss
- Overall skin structure support
FAQ
Yes, but it’s recommended to use mask on clean, dry skin. You can apply serums or moisturizers afterward to enhance the effects.
The LED face mask is designed to support multiple skin goals, including:
- Fine lines and wrinkles
- Acne-prone skin and breakouts
- Uneven skin tone and dark spots
- Dull, tired-looking skin
- Loss of firmness in the face, neck, and chest
Results may vary, but consistent use helps promote healthier-looking, more radiant skin.
For best results, use the mask 3–5 times per week.
Each session lasts 10 minutes, making it easy to fit into your daily skincare routine.Consistency is key — visible improvements typically appear within 4–8 weeks of regular use.
Yes. The mask is designed for safe, non-invasive home use and does not use UV light.
It is gentle on all skin types when used as directed.Always follow the included user manual and avoid use if you have light sensitivity conditions unless approved by a professional.